![]() ![]() Once a permit is complete and ready to be issued, we will contact the person or company that has submitted the permit application. This process may be delayed if more information is requested by the permit processors or due to an increased volume of applications. Once a permit application has been turned in to the City of Jenks at Jenks City Hall at the following address it needs a minimum of three working days to process the permit: The City of Jenks permit processor may call the homeowner or shelter/safe room company to request more information. The permit application requires information on construction, installation, zoning, and location. Who acquires the permit?Ī permit can be issued to either the homeowner or the shelter/safe room company/contractor, but both parties will need to be involved with the permit process. Homes with traditional rebar slab systems do not require this process or inspection, and a portion of the slab can be cut away for the installation of a safe room with minimal adverse effect to the foundation. An inspection of this process is required and will be made by a City of Jenks inspector before new concrete is poured or a safe room placed in the ground. It is imperative that a homeowner with this type of slab contact a professional post-tension company, such as Stresscon or Oklahoma Post Tension, to perform this work. A new section of concrete is then poured, allowed to cure, and the cables are then re-stressed. This process requires overcutting the slab on two sides of the intended installation area and installing hardware on the cut cables that will allow them to be re-stressed. In order to protect the integrity of the cable system, cables that are cut must be re-stressed. The spacing of these cables is such that a safe room installed in a slab will require the removal of a portion of two to four cables typically. These cables are stressed to high levels of tension after the slab is poured and cured and provide support to the slab and protection from settlement of the foundation. A post-tension slab has cables in the slab instead of traditional steel rebar. ![]() Homes with a post-tension cable reinforcement system in the slab require an additional step in installation and an additional inspection. It is our recommendation that you place your safe room in such a way that it is unlikely that a vehicle would need to be moved to access the safe room. The best possible location for an in-ground safe room within a garage is in a no parking area. Contact the City of Jenks for more information. If you are located in the floodplain within the City of Jenks and want to install this type of shelter, you must provide documentation that your home is elevated to this standard. In homes located within the floodplain, FEMA P-320 requires that the safe room need only be elevated to the minimum lowest floor elevation identified by the floodplain ordinance of the community. However, there are a few restrictions and considerations that must be examined with this type of shelter. Can I have a safe room installed in the floor of my existing home in a garage, closet, etc.? A permit is required to ensure compliance of the location, construction, and installation with the local codes and the guidelines established by FEMA P-320 and/or ICC-500. Some types of storm shelters and safe rooms require a permit from the City of Jenks before installation. The City of Jenks allows the installation of any storm shelters or safe rooms that meet the standards of either FEMA P-320 or ICC-500. Does the City of Jenks allow storm shelters and safe rooms to be installed for residential purposes? ![]() Please contact the City of Jenks if you want to construct this type of safe room.Ģ. These types of constructed safe rooms fall outside of the scope of this FAQ and will require additional inspections and information from the contractor. Indoor above-ground safe rooms that are constructed on site will require a permit to ensure compliance of the location, construction, and installation with the local codes and the guidelines established by FEMA P-320 and/or ICC-500.Homeowners should verify this information with their chosen safe room company. Indoor above-ground safe rooms do not require a permit if they are prefabricated to the standards of either FEMA P-320 or ICC-500.All indoor in-ground safe rooms require a permit to ensure compliance of the location, construction, and installation with the local codes and the guidelines established by FEMA P-320 and/or ICC-500.All outdoor storm shelters, require a permit to ensure compliance of the location, construction, and installation with the local codes and the guidelines established by FEMA P-320 and/or ICC-500.Which types of safe rooms and storm shelters require a permit? ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |